Pelco IS90 Uživatelský manuál

INSTALLATIONC3425M-E (1/09)IS90 SeriesCamclosure®Indoor Integrated Camera System

10 C3425M-E (1/09)InstallationYou can install the IS90 Series Camclosure integrated camera system as follows:• Mount to the surface of a ceiling/wall

C3425M-E (1/09) 11Figure 3. Ceiling/Wall InstallationFigure 4. Concrete Ceiling/Wall InstallationBACK BOXAND SURFACEMOUNT RINGWALL ORCEILING6-32 TOG

12 C3425M-E (1/09)IN-CEILING INSTALLATION: SUSPENDED CEILING1. Remove the surface mount ring from the back box (refer to Figure 5): a. Place fingers o

C3425M-E (1/09) 132. Pull the video and power wires to the selected ceiling tile.3. Mount the unit to the ceiling tile (refer to Figure 6 and Figure 7

14 C3425M-E (1/09)4. Remove an adjacent ceiling tile to access the unit.5. Connect the video cable and wires:• BNC: Connect the BNC connector from the

C3425M-E (1/09) 156. Attach the back box to the mounting surface:• If you have access behind the ceiling/wall (refer to Figure 6 on page 13):(1) Place

16 C3425M-E (1/09)5. Attach the surface mount ring and back box to the adapter plate with two 8-32 x 2.50-inch Phillips pan head self-tapping screws (

C3425M-E (1/09) 17NOTE: Failure to connect all AC powered units the same way will cause the cameras to be out of phase with each other and may produce

18 C3425M-E (1/09)Camera AdjustmentsTo perform the following camera adjustments, connect a monitor. Then turn on power to the camera and monitor. To u

C3425M-E (1/09) 19To adjust the focus:1. Loosen the focus locking screw.2. Position the inverted dome approximately 0.125 inch (3.175 mm) from the fro

20 C3425M-E (1/09)DN/CH/C SERIES ADJUSTMENTSRefer to Figure 13 to adjust the IS90-DN, IS90-CH, or IS90-C model.Figure 13. Adjusting the IS90-DN/CH/C

C3425M-E (1/09) 21SW4-4: FlickerlessIn certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be cause

22 C3425M-E (1/09)3. Each time an adjustment is made, switch back and forth between the camera you are adjusting and the reference camera. Repeat this

C3425M-E (1/09) 23DAY/NIGHT OPERATIONNOTE: This section only applies to DN model cameras.DN model cameras regularly check the brightness level of the

24 C3425M-E (1/09)DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTSRefer to Figure 15 to adjust the IS90-DW or IS90-CW model.Figure 15. Adjusting the IS9

C3425M-E (1/09) 25SW1-4: Auto White Balance/Manual White BalanceAuto white balance (AWB) is enabled by default (ON).To manually set and lock the white

26 C3425M-E (1/09)SW1-8: Day/Night Operation (DW models only)NOTE: On CW models, SW1-8 is unused and does not affect camera operation.DW model cameras

C3425M-E (1/09) 27AUTO IRIS LEVEL ADJUSTMENTThe electronics of the IS90-DW and IS90-CW Series Camclosures automatically adjust the camera to the auto

28 C3425M-E (1/09)Camera PositioningRotate and tilt the camera module to position the camera.NOTE: Do not over-rotate the module. Excessively turning

C3425M-E (1/09) 29Install Liner and Bubble1. To install the liner with a clear bubble (refer to Figure 18):a. Align the studs located on the camera mo

C3425M-E (1/09) 3ContentsRegulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 C3425M-E (1/09)Service ConnectorThe IS90 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it

C3425M-E (1/09) 31To assemble the cable:1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directions supplied with

32 C3425M-E (1/09)SpecificationsGENERALPan/Tilt Adjustment ManualPan 360°Tilt 140° (20° to 160° range) Rotation 360°ConstructionBack Box andSurface Mo

C3425M-E (1/09) 33CAMERA/LENSIf you need technical specifications for the camera itself, refer to the IS90 specification online at www.pelco.com.(Desi

34 C3425M-E (1/09)REVISION HISTORYManual # Date CommentsC3425M 2/07 Original version.C3425M-A 5/07 Updated switch setting and day/night operation desc

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USAUSA & Canada Tel (800) 289-9100 Fax (800) 289-9150Internatio

4 C3425M-E (1/09)List of Illustrations1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C3425M-E (1/09) 5Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

6 C3425M-E (1/09)DescriptionThe IS90 Series Camclosure® integrated camera system combines a camera and lens package in a small, discreet dome. The sys

C3425M-E (1/09) 7Indoor dome, surface/flush mount, smoked and clear bubble, black finishPARTS LISTCamera Type Lens/Iris NTSC PALColor, Wide Dynamic Ra

8 C3425M-E (1/09)Figure 1. Package ComponentsIS90 SERIESCAMCLOSURE WITHSMOKED BUBBLELINERADAPTER PLATECLEAR BUBBLESHOWN ACTUAL SIZESHIPPING BOX8-32 X

C3425M-E (1/09) 9Remove the BubbleTurn the bubble counterclockwise and lift (refer to Figure 2). Place the bubble on a nonabrasive surface.If the line