Pelco IS90 Uživatelský manuál

INSTALLATIONC3425M-D (8/08)IS90 SeriesCamclosure®Indoor Integrated Camera System

10 C3425M-D (8/08)Figure 3. Ceiling/Wall InstallationFigure 4. Concrete Ceiling/Wall InstallationBACK BOXAND SURFACEMOUNT RINGWALL ORCEILING6-32 TOG

C3425M-D (8/08) 11IN-CEILING INSTALLATION: SUSPENDED CEILING1. Remove the surface mount ring from the back box (refer to Figure 5): a. Place fingers o

12 C3425M-D (8/08)2. Pull video and power wires to the selected ceiling tile.3. Mount the unit to the ceiling tile (refer to Figure 6 and Figure 7):a.

C3425M-D (8/08) 134. Remove an adjacent ceiling tile to access the unit.5. Connect the video cable/wires:• BNC: Connect the BNC connector from the uni

14 C3425M-D (8/08)6. Attach the back box to the mounting surface:• If you have access behind the ceiling/wall (refer to Figure 6 on page 12):(1) Place

C3425M-D (8/08) 155. Attach the surface mount ring and back box to the adapter plate with two supplied 8-32 x 2.50-inch Phillips pan head self-tapping

16 C3425M-D (8/08)5. Connect the power wires.AC operation only: If you are wiring more than one Camclosure to the same transformer, connect one side o

C3425M-D (8/08) 17Camera AdjustmentsTo perform the following camera adjustments, connect a monitor. Then turn on power to the camera and monitor. To u

18 C3425M-D (8/08)DN/CH/C SERIES ADJUSTMENTSRefer to Figure 12 to adjust the IS90-DN, IS90-CH, or IS90-C model.Figure 12. Adjusting the IS90-DN/CH/C

C3425M-D (8/08) 19SW4-4: FlickerlessIn certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be cause

2 C3425M-D (8/08)ContentsRegulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 C3425M-D (8/08)VERTICAL PHASE ADJUSTMENTNOTE: Use this procedure for 24 VAC operation only.When using more than one camera power supply, a brief ve

C3425M-D (8/08) 21DAY/NIGHT OPERATIONNOTE: This section only applies to DN model cameras.DN model cameras regularly check the brightness level of the

22 C3425M-D (8/08)DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTSRefer to Figure 14 to adjust the IS90-DW or IS90-CW model.Figure 14. Adjusting the IS9

C3425M-D (8/08) 23SW1-4: AWB (Auto White Balance)/MWB (Manual White Balance)Auto white balance is enabled by default (ON).To manually set and lock the

24 C3425M-D (8/08)SW1-8: Day/Night Operation (DW models only)NOTE: On CW models, SW1-8 is unused and does not affect camera operation.DW model cameras

C3425M-D (8/08) 25AUTO IRIS LEVEL ADJUSTMENTThe electronics of the IS90-DW and IS90-CW Series Camclosures automatically adjust the camera to the auto

26 C3425M-D (8/08)Camera PositioningRotate and tilt the camera module to position the camera.NOTE: Do not over-rotate the module. Excessively turning

C3425M-D (8/08) 27Install Liner and Bubble1. To install the liner with a clear bubble (refer to Figure 17):a. Align the studs located on the camera mo

28 C3425M-D (8/08)Service ConnectorThe IS90 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it

C3425M-D (8/08) 29To assemble the cable:1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directions supplied with

C3425M-D (8/08) 3List of Illustrations1 Package Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 C3425M-D (8/08)SpecificationsGENERALPan/Tilt Adjustment ManualPan 360°Tilt 140° (20° to 160° range) Rotation 360°ConstructionBack Box andSurface Mo

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

4 C3425M-D (8/08)Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

C3425M-D (8/08) 5DescriptionThe IS90 Series Camclosure® integrated camera system combines a camera and lens package in a small, discreet dome. The sys

6 C3425M-D (8/08)Indoor dome, surface/flush mount, smoked and clear bubble, black finishPARTS LISTCamera Type Lens/Iris NTSC PALColor, Wide Dynamic Ra

C3425M-D (8/08) 7Figure 1. Package ComponentsIS90 SERIESCAMCLOSURE WITHSMOKED BUBBLELINERADAPTER PLATECLEAR BUBBLESHOWN ACTUAL SIZESHIPPING BOX8-32 X

8 C3425M-D (8/08)Remove the BubbleTurn the bubble counterclockwise and lift (refer to Figure 2). Place the bubble on a nonabrasive surface.If the line

C3425M-D (8/08) 9InstallationYou can install the IS90 Series Camclosure integrated camera system into any of the following:• Mount to the surface of a