Pelco DD5TA Uživatelský manuál

Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.comIn North America and Canada: Tel (800) 289-9100 or FAX (8

10 Pelco Manual C1498M-B (7/99)PAN AND TILT FUNCTIONSUse your controller’s joystick to control pan and tilt operation.• Fixed-Speed Controllers – Pan

Pelco Manual C1498M-B (7/99) 11Software controls scan limit stops. When the dome reaches one, it immediately reversesdirection. Refer to the Limit Sto

12 Pelco Manual C1498M-B (7/99)CM97501. Turn the KEY SWITCH to the ON position.2. Press the PROG key. PROGRAM appears on the LCD screen.3. Press the P

Pelco Manual C1498M-B (7/99) 13GAIN/AGCAGC ModeThe two AGC (Automatic Gain Control) modes are auto and off.• In auto mode, the dome automatically adju

14 Pelco Manual C1498M-B (7/99)6. Move the joystick up or down to position the cursor beside one of the choices. Pressthe Iris Open button.MODE – The

Pelco Manual C1498M-B (7/99) 15To change the mode:1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.2. Pre

16 Pelco Manual C1498M-B (7/99)To change the line synchronization settings:1. On the main menu, move the joystick up or down to position the cursor (&

Pelco Manual C1498M-B (7/99) 17LIMIT STOPSThe two types of limit stop are manual and scan. When manual limit stops are set, a manual(joystick) pan ope

18 Pelco Manual C1498M-B (7/99)3. Move the joystick up or down to position the cursor beside Scan Speed deg/s.4. Press the Iris Open button. The curso

Pelco Manual C1498M-B (7/99) 198. If the red power LED is lit, turn off power.a. Open the door to the interconnect circuit board and check that all co

2 Pelco Manual C1498M-B (7/99)CONTENTSSection PageIMPORTANT SAFEGUARDS AND WARNINGS ...3D

20 Pelco Manual C1498M-B (7/99)REVISION HISTORYManual # Date CommentsC1498M 2/99 Original version.3/99 Removed reference to line synchronization. Adde

Pelco Manual C1498M-B (7/99) 3IMPORTANT SAFEGUARDS AND WARNINGSObserve the following warnings before installing and using this product.1. Installation

4 Pelco Manual C1498M-B (7/99)2. Set the switches on the bottom of the dome drive. Refer to Table A for the settings forSW1, and Table B and Table C f

Pelco Manual C1498M-B (7/99) 5Receiver Address Switch SettingSW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-81 ON OFF OFF OFF OFF OFF OFF OFF2 OFF ON O

6 Pelco Manual C1498M-B (7/99)Receiver Address Switch SettingSW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-857 ON OFF OFF ON ON ON OFF OFF58 OFF ON OF

Pelco Manual C1498M-B (7/99) 7113 ON OFF OFF OFF ON ON ON OFF114 OFF ON OFF OFF ON ON ON OFF115 ON ON OFF OFF ON ON ON OFF116 OFF OFF ON OFF ON ON ON

8 Pelco Manual C1498M-B (7/99)169 ON OFF OFF ON OFF ON OFF ON170 OFF ON OFF ON OFF ON OFF ON171 ON ON OFF ON OFF ON OFF ON172 OFF OFF ON ON OFF ON OFF

Pelco Manual C1498M-B (7/99) 9225 ON OFF OFF OFF OFF ON ON ON226 OFF ON OFF OFF OFF ON ON ON227 ON ON OFF OFF OFF ON ON ON228 OFF OFF ON OFF OFF ON ON